611 industrial way west, eatontown, nj 07724 tel: 732-460- 0212 fax: 732-460-0214 sales@advanced-control.com www.a dvanced-control.com each detector model contains: ? input impedance matching ? dc return ? rf bypass capacitor ? detector diode ? video protection diode features: ? static protection ? high sensitivity ? small size applications: ? transmitter monitoring ? radar equipment ? missile guidance systems ? input to low-noise amplifiers ? broadband or narrowband ecm receivers ? power and signal monitors ? doppler radar and beacon receivers ? matched units available for mult i-channel receivers, amplitude comparator systems and discriminators minimum flatness nominal (3) frequency sensitivity vs typical (2) video standard optional range part (1) k frequency tss capacitance case case (ghz) number (mv/mw) (+/-db) (dbm) (pf) styles styles 0.1 - 1 acsm2035n 2000 0.25 -52 270 m12 m34, m35, m47 0.5 - 2 acsm2001n 2000 0.4 -53 75 m12 m34, m35, m47 1 - 2 acsm2066n 2000 0.2 -53 20 m12 m34,m35,m47,m50,m51 0.5 - 4 acsm2108n 2000 0.4 -53 20 m12 m43, m50, m51 1 - 4 acsm2038n 2000 0.4 -53 20 m12 m50, m51 2 - 4 acsm2002n 2000 0.4 -53 20 m12 m50, m51 1 - 8 acsm2075n 2000 0.5 -53 20 m12 ? 2 - 8 acsm2014n 2000 0.5 -53 20 m12 ? 4 - 8 acsm2003n 2000 0.4 -53 20 m12 m50, m51 2 - 12 acsm2007n 2000 0.9 -52 20 m12 ? 8 - 12 acsm2004n 2000 0.65 -52 12 m12 ? 1 - 18 acsm2047n 1800 1.0 -51 20 m12 ? 2 - 18 acsm2006n 1800 1.0 -51 12 m12 ? 8 - 18 acsm2015n 1800 0.7 -52 12 m12 ? 12 - 18 acsm2005n 2000 0.6 -52 12 m12 ? notes: 1) standard output polarity is negative. if negative output is required, substitute ?p? for ?n? in part number. 2) tangential signal sensitivity (tss) is a measure of low level sensitivity with respect to noi se. it is measured using a vid eo amplifier with a 2mhz bandwidth and a 3db noise figure. 3) video capacitance is used for rf bypass. this value can be changed if required for video response time or other considerati ons. contact the factory if value other than those shown are needed. 4) video protection is available on most models. this feature helps to prevent damage to the detector diode from incidents occ urring at the video port. transient electromagnetic spikes, static contact, or voltage surges can ea sily damage a detector diode. a video p rotection diode will clamp the voltage at a value less than the detector break down voltage. note: inclusion of this protection will caus e the output voltage to compress and clamp. this occurs at about + 10dbm input to the detector. if operation above +10dbm is require d then the output protection should be modified or ex cluded. adding a suffix ?x? at the end of the model number will exclude the vide o protection feature. contact the factory for assistance. 5) zero bias schottky ve rsions are available for most of listed biased schottky models with onl y minor differences in specifica tions. a. the zero bias schottky has an impedance of several thousand ohms. b. zero bias schottky detecto rs exhibit less sensitive tss due to the high diode impedance (typically a 3db reduction). c. the temperature performance of the zero bias schottky is poor when operating at low input power levels. this difference becomes small at high levels (above 0dbm input power). the part number of zero bias versions includes a ?z? following the polarity indicator. high sensitivity and superior electrical and environmental reliability characterize these module detectors. they are hermetically sealed and contain internal rf matching, dc return, and rf bypass capac itor. in addition, the video port can be protected from static or transient voltages. this feature prevents damage due to handling (usually static) or system video transients. models may be chosen for broadband rf performance or for optimized narrow bands. they may be used in microstrip or stripli ne applications for power monitoring, broadband ecm receivers, radar equipment, beacon or multi-channel receivers. schottky diode module detectors
611 industrial way west, eatontown, nj 07724 tel: 732-460- 0212 fax: 732-460-0214 sales@advanced-control.com www.a dvanced-control.com 0.129 ?0.012 typ. 0.330 input 0.120 0.080 0.246 .003 output 0.250 0.120 0.058 typ. c l 0.050 (3) plcs. 1 2 3 4 0.015.003 typ. 0.150 0.400 max. 0.210 0.180 sq. max. ground n/c output n/c ground n/c rf input n/c 8 7 6 5 4 3 2 1 pin function 0.005.002 0.080 max. 8 7 6 5 0.004 x 0.020 min. (2) plcs. 0.020 max. (to flat) 0.280.005 0.160 0.205.003 0.135 .010 (2) plcs. ?0.096.003 thru 0.126 .004 0.062.002 0.079.002 0.080 .001 colored dot input ?0.500.002 ?0.450.002 0.200 0.185.015 0.031.003 0.050 max. 0.300.005 0.018.002 (4) plcs. 453 typ. rf in n/c video out gnd rf in video out n/c gnd ?0.360.002 ?0.300.002 0.160 0.185.015 0.031.003 0.034.005 453 typ. 0.200.005 typ. 0.018.002 (4) plcs. environmental specifications: screening : mil-e-5400, mil-std-202, mil-e-16400 standard screening : operating temp: -65c to +125c internal visual per mil-std-883, method 2017 storage temp: -65c to +150c temperature cycle: -65c to +100c, 10 cycles humidity: mil-std-202f, m103, cond b op tional high-rel screening (ref mil-prf-38534) : shock: mil-std-202f, m213, cond b internal visual per mil-std-883, method 2017 altitude: mil-std-202f, m105, cond b stabilization bake per mil-std-883, method 1008 vibration : mil-std-202f, m204, cond b temperature cycle per mil-std-883, method 1010 thermal shock: mil-std-202f, m107, cond a c onstant acceleration per mil-std-883, method 2001 temperature cycle: mil-std-202f, m105c, cond d burn-in per mil-std-883, method 1015 maximum input power: +20dbm leak test per mil-std-883, method 1014 external visual per mil-std-883, method 2009 case style m12 case style m47 case style m50 case style m51 case style m43 case style m34 case style m35 part number ordering information: example: acsm2015nzm51x20 acsm2015: schottky module detector, 8 - 18ghz n: negative output polarity z: zero bias version (omit for biased version) m51: package type x: no video protection (omit for inclusion of video protection) 20: 20pf custom output ca pacitance (omit for standard value) sm-0205 ?0.015 typ. 0.430 0.120 0.080 ?0.187 .003 0.250 0.120 0.0520.004 (2) plcs. 0.094 0.1015 c l +.0015 -.0000 ?0.058.003 thru (2) plcs. 0.126.004 0.080.001 0.161.001 0.205.003 colored dot input 0.062.002 0.135.010 (2) plcs. 0.252.003 0.411.002 0.079.002 0.004 x 0.020 min. (2) plcs. 0.012 max. (to flat)
|
